building valuations

EXTERNAL FEATURE DEFINITIONS

The definitions below are for features found on the outside of a building.

CHIMNEYS AND ROOFS

Party Structures Defined - Party Wall Act Etc. 1996
A structure which both parties enjoy the use of or benefit from.   An example of this would be where both parties gain support from a wall or utilise a chimney or chimneys.

Any work to party structures, such as party walls or party chimney stacks, require agreement under the Party Wall Act.   We would be more than happy to offer you help and advice in this matter.

Tile on Edge Defined
A tile sitting sideways, bedded in cement mortar which has been utilised as a flashing.   Due to the cement mortar it is bedded in being brittle and prone to cracking, this is not an ideal material.   We would always recommend the use of lead flashings.

Flaunchings Defined
A low, wide cement mortar fillet surrounding the flue terminal on top of the chimney stack to throw off rainwater.

Free phone 0800 298 5424

Flashings Defined
Flashings prevent dampness from entering the property, usually at junctions where materials change.   Such a junction is the one between the chimney and the roof.

Spalling Defined
Spalling occurs to brick or stone when water penetrates the surface and via freezing and thawing starts to cause deterioration to the surface. This in turn allows further water penetration and the surface breaks up further.   This ultimately can lead to water damage or structural damage to the area.

Re-Pointing Defined
Re-pointing is carried out where the existing mortar has failed and broken away to stop damp penetration and further deterioration.   The mortar should be raked out to approximately 20mm and then replaced with a mortar of a similar type, therefore, stopping damp occurring.

Capping Defined
Capping is a practice used when chimneys are no longer in use to prevent moisture from entering the structure in the form of rainwater via the chimney.   This usually involves the closing of the chimney with a tile or slab positioned across.   It should include vents to allow air circulation.

Parapet Walls Defined
These walls are usually above the roof line and often sit on the boundary of the property.   Due to their position they are relatively exposed and suffer from deterioration due to the elements.

Blinding Defined
This is where a mortar is used to bed the slate or tile.

Polycarbonate Defined
Transparent, extremely tough plastic sheet, used for security glazing.   It may also be an insulating light panel, double walled or triple walled, or 10 or 16mm thick.   It is not a fire hazard as it has low ignitability and low flame spread, and releases little heat and little smoke if burnt.   It can be coated to resist damage from ultraviolet.

Flashband Defined
Flashband is a sticky backed felt which is best used for temporary repairs only.

Proprietary Flashings Defined
These are typically supplied by the manufacturer of the roof covering and will be specially made to fit the profile of the roof covering.   Typically they are aluminium.

Cement Fillets/Cement Flashings
This is where cement has been used to cover up or fill the junctions between two areas, for example between a roof and a wall to help prevent dampness. Cement is a brittle material and prone to cracking which in turn allows dampness into the structure. We would always recommend they are replaced with lead.

Torching Defined
Usually lime mortar dabs (but can be moss) which the slates sit upon.   These are used to reduce the wind traveling through the building therefore reducing the risk of wind damage.

Nail Sickness Defined
The weakening of the fixing nails to slates or tiles due to the nails which fix them to the battens rusting.   This is normally attributed to problems with slate roofs.

Lead Tingles or Lead Slaps Defined
These are strips of lead usually about 25mm wide which are used to secure slates where they have slipped.

Turnerising Defined
"Turnerising" is a process used usually when roofs have started to deteriorate or leak and it involves the covering of a roof with a mesh and coating in bitumen.   It is almost impossible to economically save or re-use materials which have been treated in this manner.

Nibbed Clay Tiles Defined
A nibbed tile is one which has raised areas known as nibs, usually two in number, at the top of the tile to enable the tile to be fixed to the roof batten which, in turn, fixes to the roof structure.

Blinding Defined
This is where a mortar is used to bed the slate or tile.

Polycarbonate Defined
Transparent, extremely tough plastic sheet, used for security glazing.   It may also be an insulating light panel, double walled or triple walled, or 10 or 16mm thick.   It is not a fire hazard as it has low ignitability and low flame spread, and releases little heat and little smoke if burnt.   It can be coated to resist damage from ultraviolet.

Flashband Defined
Flashband is a sticky backed felt which is best used for temporary repairs only.

Proprietary Flashings Defined
These are typically supplied by the manufacturer of the roof covering and will be specially made to fit the profile of the roof covering.   Typically they are aluminium.

Delamination Defined
This occurs in sedimentary and metamorphic rocks such as slate which are built up of layers.   It simply refers to the layers breaking down.

WITHIN THE ROOF SPACE

Sarking Felt/Underfelt Defined
This is the felt that sits between the roof covering and the timber battens and forms an additional protective layer to stop the wind lifting the roof and to stop the elements from penetrating the structure.   This was first used in the late 1940's/early 1950's and is a requirement for current Building Regulations.

Close Boarding Defined
These are timbers positioned on the common rafters which are butt jointed together.   They add to the wind resistance and water-tightness of the roof together with the overall structural integrity of the roof. Usually this type of roof does not have an underfelt, this can lead to problems if the roof is not cross-battened as wet rot will occur to the underside of the timbers. This is very difficult to identify.

Feather Edge Boarding Defined
These are timbers positioned on the common rafters which form the slope of the roof. These timbers are butted together but they are cut at an angle, or feather edged, to give a lip for the nibs of the tiles to sit upon.

Fire Walls Defined
Fire walls help prevent the spread of fire through roofs and are a relatively recent Building Regulation requirement .

Purlins Defined
The purlin is the horizontal timber member usually running from gable end to gable end and parallel with the walls which supports the jack or common rafters (the angled rafters forming the slope to the roof).

Ridge Board Defined
The ridge board forms the apex of the roof and usually denotes that the roof was constructed on site and joins the jack rafters or common rafters together.   These are the rafters that form the slope to the pitch of the roof.

Common Rafters Defined
The rafters form the slope to which the battens are secured and in turn the roof covering is also secured too.

Couple Roof Defined
A traditional pitched roof with rafters and no tie beam, used for short spans up to 3m, assuming standard joist centres.

Close-Couple Roof Defined
This is a traditional framed roof with common rafters joined at the wall-plate level with a tie beam, also used for ceiling joists, used for spans up to about four metres, assuming standard joist centres.

King Post Truss Defined
A traditional timber roof truss with a vertical post from the apex to the centre of the bottom tie beam, suitable for spans up to about 11m, but like the queen-post truss not now used for new work in Britain.

Prefabricated Truss Defined
This is a roof truss made in a factory using gang nails at the joints, it is then transported to the site and normally lifted into place.   This type of construction has been used for about the past 30 to 40 years.

Wall Plates Defined
Wall plates are the horizontal members normally timber, although they sometimes can be metal RSJ's, fixed to the top of the wall within the roof space.   They hold the common rafters from the roof in place but can be susceptible to dampness.

Battens Defined
A small section, normally of timber, to which sheet materials, slates and roof tiles are fixed.

Wind Bracing Defined
These are timbers fixed across the roof structure to stop movement when it is windy.

GUTTERS AND DOWNPIPES

Surcharging Defined
This term is usually used in relation to valley gutters and is where there is too much rain for the valley gutter to cope with.

WALLS

Cornice Defined
This is the top course of bricks where the house meets the roof.

Efflorescence Defined
This is where salts appear on the surface of the brickwork in a white dust or crystal formation

Lime Mortar Defined
mix used to bed bricks upon; its characteristics being that it flexes and moves with the structure.   It was used up to the War years.

Cement Mortar Defined
sand cement mix used commonly in brick houses from about the First World War onwards and is relatively strong and brittle and therefore does not allow much movement.

Re-Pointing Defined
Re-pointing is carried out where the existing mortar has failed and broken away to stop damp penetration and further deterioration.   The mortar should be raked out to approximately 20mm and then replaced with a mortar of a similar type, therefore, stopping damp occurring.

Engineering Brick Defined
A clay brick of high compressive strength and low absorption, eg Staffordshire blue bricks and some reds.   Class A bricks are stronger than 70 N/mm² and have an absorption below 4.5%.   Class B have a 50 N/mm² compressive strength and maximum 7% water absorption.

Fletton Brick Defined
A low cost pale red brick made from Oxford clay with traces of coal that burn during firing, saving energy.   It is pressed like many clay bricks and can be sand faced, pigmented, or textured for use as facings.

Bonding Timbers Defined
These are timbers used in construction of walls usually using a lime mortar construction. Bonding timbers are used horizontally and add strength to the wall enabling additional lifts of brickwork.

Render Defined
A sand and cement external coating applied in two or three coats or layers.

Bell-Mouths Defined
A bell-mouth is a curve at the base of a wall which throws the water away from the structure therefore preventing dampness.

Pier Defined
This can be the load bearing brickwork in a wall between openings, or a short buttress on one or both sides of a wall, bonded to it for stability.

Cavity Wall Ties Defined
A fastener across a cavity wall to hold the two leaves together.   Usually made of stainless or galvanised steel wire or strip, sometimes plastic, and has a twist or bend near the middle to form a drip so that water cannot pass.   Wall ties are built into the brickwork bed joints as work proceeds and may have a large plastics washer to hold cavity insulation in place.

Recessed Joint Defined
A mortar joint set back about 6mm from the face of the wall, either a raked-out joint or one made by tooling. It is used for brickwork, and for stonework to prevent flushing, and is strongly shadowed.

FOUNDATIONS

London Clay in General
This property stands on London Clay as with the majority of properties in London.   It is therefore more susceptible than most should drains leak or trees be allowed to overgrow etc.   It is not unusual to have some settlement in London properties and from our inspection of the walls we have found nothing unusual.  

TREES

Influencing Distance Defined
This is the distance in which a tree may be able to cause damage to the subject property.

EXTERNAL JOINERY

Over Lights Defined
This is a window above the door allowing light into the hallway area.

Secondary Glazing Defined
This is where a secondary window has been added, usually to prevent draughts.   We would also draw to your attention that these type of windows can be restrictive in the case of the emergency when, for example, a fire has occurred in the property.

Trickle Vents Defined
Small vents to the windows to allow air movement inside the property to stop a build up of fumes or humidity.

 

[ Back to definitions main page ]

 

building engineers
Home Buyers Reports Property Surveys - why we're the best. Engineers Reports
© Copyright 1stassociated.co.uk
Site Map

1stassociated-logo-for-footer IVSA-badge IVSA-putting-client-first call-us-for-footer

We have thousands of free property articles to help you - or call us freephone on 0800 298 5424

We have been working in the property industry for many years and have been
providing free property articles for over ten years. All for free and to help you with buying your next property.

House and Home Surveys and Useful Information

All you need to know about Building Surveys

Building Control, what do they do?

Designers and Architects will they save me money or will they cost me money

Enviroment, Your Building and Garden Gnomes

Estate Agents help sell houses and work for the vendors

Have a Structural Survey to protect you against structural problems

Home improvements, builder problems and ideas for you on how to solve them

How a Surveyor values a property, Chartered Surveyors and Regulated Valuers

How Chartered Engineers and Building Engineers can help you

Listed Buildings and Conservation Areas

NHBC National House Building Council

Structural Surveys and How We Can Help You

Traditional and Non-Traditional Houses and Mortgage Problems

Valuations and how much is the building worth?

Whats the difference between a Chartered Building Surveyor, Chartered Surveyor and an Independent Surveyor

Useful property problem articles by Chartered Surveyors explaining building issues to avoid

External - Helpful information on building problems on the outside of the property

Chimney issues and problems

Cracking and Movement Problems and Surveying Solutions

Flat Roof Problems, how we can solve them

Foundations and Structures and Settlement and Subsidence and Underpinning

Pitched Roofs Problems and Solutions

Roof Problems

Wall Problems

Windows and Doors and Fascias and Soffits and Wet Rot and Dry Rot and other problems

Internal - House problems we have investigated inside

All you ever need to know about floors

Asbestos in your home, what you need to know

Ceiling Cracks and Structural Problems

Condensation, Damp and Black Mould Problems

Cracking and Movement Problems and Surveying Solutions

Windows and Doors and Fascias and Soffits and Wet Rot and Dry Rot and other problems

Woodworm is it a problem or not? Is it active or not?

Services - Building help and advice on costly services

Drainage, what's underground can affect what's above ground

Heating; I just can't get my house warm enough or alternatively I just can't get my house cool enough

You can't mess around with the electric, you need an expert

 

Commercial Property Services

Building Terms Explained and Directories

Commercial Property Surveys

Commercial Structural Surveys

Leisure Facilites

Offices Large and Small

Shops and Retail

Warehouse and Industrial Buildings

Dilapidations Help and Advice What is a Dilapidations Notice?

A Beginner's Guide to Dilaps

Damp Mould and Condensation

Dampness Rising Damp Mould Black Mould Condensation

Dilapidations and Negotiations

Dilapidations Claim by a Landlord

Energy Saving what can I do?

Finance what is a Financial Adviser (We are not Financial Advisors)

Fire Risk and Help

Health and Safety Risks

Insurance how do I get the correct property insurance?

Landlords Surveying Advice

Property Investment how can I invest in property?

Property TV Reviews by an Independent Surveyor

Schedules of Condition Leasing a Commercial Property

Scotts Schedule and Section 18 Valuation

Tenants Surveying Advice

Weather how does weather affect my property?

Flooding

Rain

Snow and Ice

Strong Winds

Reviews from clients on Commercial Building Surveys

Churches and Charities, helpful reviews from our clients

Industrial Buildings and Warehouses and what our clients say about us

Offices Large and Small, reviews and feedback from our clients

Pubs, Restaurants, Hotels and other Leisure facilities we have surveyed over the years

Shops and Retail, helpful reviews from our clients

 

First Time Buyers

Buying a Leasehold or Shared Freehold Home

Buying and Selling Houses for the experienced house and home purchaser

First Time Buyers how do I go about buying my first house and home?

Improve your property knowledge with our presentations on house, homes and commercial property

Building Surveys

Building Surveying Useful Information

Dilapidations

Dilapidations Presentations in Detail

Final Year Building Surveying Exams for University Students or those that would like to know more

How old is your Building? Which era was it built in?

Party Walls

Surveyors and Design Tools

Disputes and Party Walls

Boundary Disputes

Building and Property Disputes

Party Wall Book Reviews

Party Walls Your Rights and Responsibilities

1stAssociated Surveyors Review for Structural Surveys and Building Surveys

Building Surveys, reviews and feedback from satisfied customers

Buy to let property clients, what they say about our structural surveys

Buying at auction, review of the survey

Buying bungalows and retirement properties and how our surveyors can help

Both at work / busy couples, how we can help and some 1stAssociated client reviews

Families with a young person flying the nest, reviews and feedback

First Time Buyers, what they say about us

Listed buildings, structural surveys

Older buildings, a review of buying an older house

Families with children looking for a new home, feedback and reviews

Buying a Non-Traditional Property

Residential Surveys

House and Home Surveys

Commercial Building Surveys

Commercial Surveys

1st Associated Surveyors Are Also Available in the Following Areas:

East Anglia and East

South and South East

West Country and South West

Midlands

North and North East

 

London

London Markets

London Parks

 

Wales

Areas of Britain

1stAssociated Independent Expert Property Surveyors

Specialists in Home Buyers Reports, Building Surveys and Structural Surveys and Schedules of Condition

All Surveyors are Royal Institution of Chartered Surveyors qualified and RICS regulated

and are Members of the Independent Surveyors and Valuers Association

Putting the Client First

We do not accept service of documents by email or fax